All about Ford Mondeo

Interior trim panels - removal and refitting
Bodywork and fittings / Interior trim panels - removal and refitting


Removal
Sun visor
1 Disconnect the wiring for the vanity mirror light, where fitted.

2 Unscrew the mounting screws and remove the visor.

3 Prise up the cover, unscrew the inner bracket mounting screws, and remove the bracket.

Passenger grab handle
4 Prise up the covers, then unscrew the mounting screws and remove the grab handle.

УAФ pillar trim
5 Pull away the door weatherstrip in the area of the trim.

6 Release the alarm and aerial wiring from the upper and middle clips.

7 Carefully press the trim away from the upper and middle clips, and pull the trim upwards. Recover the lower sealing strip.

8 Remove the upper and middle clips from the pillar.

УBФ pillar and cowl side trim 9 Pull away the door weatherstrip in the area of the trim.

10 Undo the screws, release the fasteners and remove the lower trim (see illustrations).

29.10A Removing a middle screw from the lower trim
29.10A Removing a middle screw from the lower trim

29.10B Releasing the fasteners from the cowl side trim
29.10B Releasing the fasteners from the cowl side trim

11 Carefully separate the lower trim from the upper trim, using a screwdriver if necessary (see illustration).

29.11 Separating the УBФ pillar lower and upper trim
29.11 Separating the УBФ pillar lower and upper trim

12 Unscrew the seat belt mounting bolt from under the front seat, remove the remaining trim from the УBФ pillar, and feed the belt through the trim.

УCФ pillar trim (Saloon and Hatchback) 13 Pull away the door weatherstrip in the area of the trim.

14 Fold the rear seat cushion forwards.

15 Pull up the rear seat bolster, and release the upper hook. Note that, on low-series models, the bolster is retained with a screw (see illustrations).

29.15A Pull up the rear seat bolster . . .
29.15A Pull up the rear seat bolster . . .

29.15B . . . and release the upper hook
29.15B . . . and release the upper hook

16 Undo the screw, release the clips, and detach the upper trim.

17 Remove the rear seat belt lower mounting bolt, then remove the trim, and pass the seat belt through it.

УCФ pillar trim (Estate) 18 Prise off the caps, unscrew the screws, and remove the upper trim from the УCФ pillar (see illustration).

29.18 Screw locations (arrowed) for the УCФ pillar upper trim - Estate
29.18 Screw locations (arrowed) for the УCФ pillar upper trim - Estate models

19 Unscrew the mounting bolt securing the rear seat belt upper shackle to the УCФ pillar.

20 Unclip and remove the trim.

УDФ pillar trim (Estate) 21 Remove the three mounting screws, then unclip the trim from the УDФ pillar.

Lower facia panel
22 Remove the steering column top and bottom shrouds.

23 Unscrew the mounting screws from the upper corners and above the coin tray position, and withdraw the lower facia panel from the facia (see illustrations).

29.23A Unscrew the mounting screws from the upper corners . . .
29.23A Unscrew the mounting screws from the upper corners . . .

29.23B . . . and above the coin tray position . . .
29.23B . . . and above the coin tray position . . .

29.23C . . . and withdraw the lower facia panel
29.23C . . . and withdraw the lower facia panel

Refitting
24 Refitting is a reversal of the removal procedure. Where seat belt fastenings have been disturbed, make sure that they are tightened to the specified torque.


© 2018 www.fordmon.ru. All Rights Reserved.