All about Ford Mondeo

Switches - removal and refitting
Body electrical system / Switches - removal and refitting


Removal
Ignition switch and lock barrel 1 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

2 Remove the rubber gaiters and locking rings, then remove the securing screws and take off the steering column upper and lower shrouds.

3 Insert the ignition key, and turn it to the accessory position. Using a small screwdriver or twist drill through the hole in the side of the lock housing, depress the locking plunger and withdraw the lock barrel (see illustrations).

4.3A Depress the locking plunger . . .
4.3A Depress the locking plunger . . .

4.3B . . . and withdraw the ignition lock barrel
4.3B . . . and withdraw the ignition lock barrel

4 The switch may be removed from the steering column assembly by disconnecting the multi-plug, then using a screwdriver to release the switch retaining tab (see illustrations).

4.4A Release the retaining tab . . .
4.4A Release the retaining tab . . .

4.4B . . . and remove the ignition switch
4.4B . . . and remove the ignition switch

Windscreen wiper multi-function switch
5 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

6 Remove the rubber gaiters and locking rings, then remove the securing screws and take off the steering column upper shroud.

7 Disconnect the multi-plug (see illustration).

4.7 Disconnecting the multi-plug from the windscreen wiper multi-function
4.7 Disconnecting the multi-plug from the windscreen wiper multi-function switch

8 Depress the plastic tab with a screwdriver, and lift the switch assembly from the steering column (see illustrations).

4.8A Depress the plastic tab with a screwdriver . . .
4.8A Depress the plastic tab with a screwdriver . . .

4.8B . . . and remove the windscreen wiper multi-function switch
4.8B . . . and remove the windscreen wiper multi-function switch

Main light, auxiliary foglight and rear foglight combination switch Note: From July 1994 a rvised main light switch was introduced; this was fitted as standard in production. If the revised switch is to be fitted to a pre-July 1994 model, an adapter lead will also be required to prevent electrical damage ocurring. Refer to your Ford dealer for further information 9 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

10 Carefully prise the switch panel from the facia, using a screwdriver against a cloth pad to prevent damage to the facia (see illustration).

4.10 Prising out the light switch
4.10 Prising out the light switch

11 Disconnect the multi-plugs and withdraw the switch panel (see illustration).

4.11 Disconnecting the multi-plugs from the light switch and rheostat
4.11 Disconnecting the multi-plugs from the light switch and rheostat

12 Unscrew the four mounting screws, and remove the switch from the panel.

13 Pull off the switch control knob, and remove the blanking plug and retainer.

14 Depress the plastic tabs, and remove the front cover and switch.

Instrument light rheostat 15 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

16 Carefully prise the light switch panel from the facia, using a screwdriver against a cloth pad to prevent damage to the facia.

17 Disconnect the multi-plugs from the rear of the switch, then remove the screws and withdraw the instrument light rheostat from the panel.

Door mirror control switch 18 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

19 Carefully prise the switch from the facia, using a screwdriver against a cloth pad to prevent damage to the facia.

20 Disconnect the multi-plug and withdraw the switch.

Direction indicator, dipped beam and hazard flasher multi-function switch 21 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

22 Remove the rubber gaiters and locking rings, then remove the screws and take off the steering column upper shroud.

23 Depress the retaining lug and withdraw the switch assembly, then disconnect the multi-plug (see illustration).

4.23 Removing the direction indicator, dipped beam and hazard flasher
4.23 Removing the direction indicator, dipped beam and hazard flasher multifunction switch. Direction indicator relay (flasher unit) is attached

24 With the switch assembly removed, pull out the direction indicator relay if required.

Horn switch (steering wheel without air bag)
Note: When an air bag is fitted, the horn switch is removed with the air bag unit. Refer to Section 28.

25 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

26 Carefully pull off the padded centre of the steering wheel which incorporates the horn switch.

27 Disconnect the wiring and remove the switch assembly.

Luggage compartment switch 28 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

29 With the tailgate/bootlid open, pull the weatherstrip from the centre of the rear cross panel.

30 Carefully prise out the trim fasteners from the bottom corners of the rear trim, then unscrew the retaining screws and remove the trim panel.

31 Disconnect the wiring multi-plug, and pull out the switch.

Electrically-operated window switch (single)
32 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

33 Carefully prise out the switch from the door inner trim panel, using a cloth pad to prevent damage to the trim.

34 Disconnect the multi-plug and remove the switch.

Electrically-operated window switch (multiple) and isolator
35 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

36 Prise the blanking cap from inside the inner door handle cavity, and remove the screw.

37 Hold the inner door handle in its open position, then remove the bezel and withdraw it over the handle.

38 Depress the retaining lug and remove the switch assembly, then disconnect the multiplug.

Electrically-operated sunroof switch and traction control switch 39 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

40 Carefully prise out the switch with a screwdriver, using a cloth pad to prevent damage to the trim.

41 Disconnect the multi-plug and remove the switch.

Handbrake-on warning switch 42 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

43 Remove the centre console as described in Chapter 11.

44 Disconnect the multi-plug, then remove the screw and withdraw the switch from the handbrake lever mounting bracket (see illustration).

4.44 Disconnecting the multi-plug from the handbrake lever
4.44 Disconnecting the multi-plug from the handbrake lever

УEconomy/SportФ mode switch automatic transmission models) 45 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

46 Select Neutral, then prise out the selector indicator panel, using a cloth pad to prevent damage to the surrounding trim.

47 Push the switch out of the panel, and disconnect the multi-plug.

Heated windscreen switch and heated rear window switch
48 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

49 Carefully prise out the switch, using a cloth pad to prevent damage to the trim (see illustration).

4.49 Prising out the heated rear window switch
4.49 Prising out the heated rear window switch

50 Disconnect the multi-plug and remove the switch (see illustration).

4.50 Disconnecting the multi-plug from the heated rear window switch
4.50 Disconnecting the multi-plug from the heated rear window switch

Electrically-operated seat switch and heated seat switch
51 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

52 Carefully prise out the switch, using a cloth pad to prevent damage to the trim.

53 Disconnect the multi-plug and remove the switch.

Adaptive damping switch
54 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

55 Carefully prise out the switch, using a cloth pad to prevent damage to the trim.

56 Disconnect the multi-plug and remove the switch.

Courtesy light door switch 57 Open the door, then unscrew the crosshead screw and carefully pull the switch from the pillar (see illustrations). Take care not to force the wire from the switch terminal, otherwise it will be difficult to retrieve it from the pillar.

4.57A Unscrew the cross-head screw . . .
4.57A Unscrew the cross-head screw . . .

4.57B . . . and pull out the courtesy light switch
4.57B . . . and pull out the courtesy light switch

58 Disconnect the wire, and tie it in a loose knot to prevent it dropping back into the pillar.

Refitting
59 Refitting of all switches is a reversal of the removal procedure.


© 2018 www.fordmon.ru. All Rights Reserved.