All about Ford Mondeo

Bulbs (interior lights) - renewal
Body electrical system / Bulbs (interior lights) - renewal


Engine compartment light 1 With the bonnet open, pull the wedge-type bulb from the bulbholder.

2 Fit the new bulb using a reversal of the removal procedure.

Interior lights
3 Switch off the interior light by locating the switch in its middle position.

4 Using a small screwdriver, carefully prise out the light or bulb cover, as applicable (see illustration).

6.4 Prise out the interior light with a screwdriver
6.4 Prise out the interior light with a screwdriver

5 Lift up the reflector, then release the festoon-type bulb from the contact springs (see illustration).

6.5 Lifting the reflector from the interior light
6.5 Lifting the reflector from the interior light

6 Fit the new bulb using a reversal of the removal procedure. Make sure that the tension of the contact springs is sufficient to hold the bulb firmly.

Reading light
7 With the reading light switched off, prise out the light using a small screwdriver.

8 Hinge back the contact plate, and release the festoon-type bulb from the contact springs.

9 Fit the new bulb using a reversal of the removal procedure. Make sure that the tension of the contact springs is sufficient to hold the bulb firmly.

Instrument panel illumination and warning lights
10 Remove the instrument panel as described in Section 10.

11 Twist the bulbholder anti-clockwise to remove it (see illustration).

6.11 Removing a bulb from the rear of the instrument panel
6.11 Removing a bulb from the rear of the instrument panel

12 Fit the new bulbholder using a reversal of the removal procedure.

Foglight warning indicator 13 Using a screwdriver, prise out the indicator from the facia, and disconnect the multi-plug.

14 Twist the bulbholder anti-clockwise with the screwdriver, and remove it (see illustration).

6.14 Removing the bulb from the foglight warning indicator
6.14 Removing the bulb from the foglight warning indicator

15 Fit the new bulb using a reversal of the removal procedure.

Hazard warning light
16 Pull the cover directly up from the switch, then remove the bulb (see illustrations).

6.16A Pull off the hazard warning light cover . . .
6.16A Pull off the hazard warning light cover . . .

6.16B . . . and remove the bulb
6.16B . . . and remove the bulb

17 Fit the new bulb using a reversal of the removal procedure.

Glovebox light
18 Open the glovebox, then pull out the wedge-type bulb from the light located under the upper edge.

Heater fan switch illumination 19 Pull off the switch knob, then depress and twist the bulb to remove it.

Automatic transmission selector panel illumination
20 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

21 Remove the ashtray.

22 Select Neutral, then prise out the panel from the centre console.

23 Disconnect the multi-plug from the overdrive control switch.

24 Disconnect the bulbholder and pull out the wedge-type bulb.

25 Fit the new bulb using a reversal of the removal procedure.

Interior door handle illumination 26 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

27 Remove the door interior trim panel as described in Chapter 11.

28 Using a knife, cut free the foam watershield for access to the rear of the interior door handle.

29 Pull out the bulbholder and remove the bulb.

Clock illumination
30 Disconnect the battery negative (earth) lead (refer to Chapter 5, Section 1).

31 Remove the clock as described in Section 13.

32 Twist the bulbholder anti-clockwise using a screwdriver, then remove the bulbholder from the rear of the clock (see illustrations).

6.32A Twist the bulbholder anti-clockwise . . .
6.32A Twist the bulbholder anti-clockwise . . .

6.32B . . . and remove it from the rear of the clock
6.32B . . . and remove it from the rear of the clock

Heater control illumination 33 Remove the heater control panel (Chapter 3), then twist the bulbholder anti-clockwise and remove the bulb from the rear of the panel.


© 2018 www.fordmon.ru. All Rights Reserved.